2-Piece Front Complete Strut & Coil Spring Assembly Set for 2005-2010 Ford Mustang
Available in stock (20)
2-Piece Front Complete Strut and Coil Spring Assembly Set
Front suspension replacement set for source-listed 2005–2010 Ford Mustang applications. The supplied information identifies two complete strut and coil-spring assemblies covering the driver and passenger sides.
Critical fitment warning: Mustang front suspension components can vary by engine, trim, body style, production date, factory suspension package, ride-height specification, and performance model. The source provides one broad 2005–2010 Mustang range but does not identify those configurations. Confirm the VIN, exact model and trim, Coupe or Convertible body, engine, production date, original spring and strut dimensions, mounting points, brackets, ride height, and reference number before ordering.
Source-Listed Compatibility
- 2005 Ford Mustang
- 2006 Ford Mustang
- 2007 Ford Mustang
- 2008 Ford Mustang
- 2009 Ford Mustang
- 2010 Ford Mustang
Position: Front driver and passenger sides.
Not confirmed: Exact V6 or V8 coverage, Base, GT, Bullitt, Shelby GT500, Shelby GT, Saleen, Roush, Coupe, Convertible, special-edition, lowered, track-package, police-package, electronically controlled, or modified suspension applications. Do not treat the broad year range as proof of every Mustang configuration.
Package Contents
- 1 × Front driver-side complete strut and coil-spring assembly
- 1 × Front passenger-side complete strut and coil-spring assembly
Total quantity: 2 front assemblies.
The source explicitly identifies complete strut and coil-spring assemblies but does not separately confirm every preinstalled component. Upper mounts, mount bearings, spring seats, isolators, dust boots, bump stops, brackets, nuts, and mounting hardware must be verified from the product images and received parts before installation.
Product Details
- Product type: Complete front strut and coil-spring assembly set
- Position: Front left and front right
- Quantity: 2 assemblies
- Source-listed vehicle: 2005–2010 Ford Mustang
The source does not provide spring rate, extended or compressed length, piston-rod diameter, tube diameter, gas charge, damping specification, ride height, load rating, color, reference numbers, or individual assembly dimensions. Compare the original parts and mounting geometry before installation.
Installation Notes
Professional installation is recommended. Suspension components store substantial energy and affect steering, braking, tire contact, and vehicle control. Safely support the vehicle and follow the model- and configuration-specific service procedure.
Before removal, compare both replacement assemblies with the original parts for overall length, spring diameter and shape, upper-mount pattern and orientation, lower mounting points, brake-hose and wheel-speed-sensor brackets, clearance, and left/right identification. Do not interchange sides unless the components and service information specifically permit it.
Inspect the steering knuckles, control arms, ball joints, tie-rod ends, stabilizer links and bushings, wheel bearings, brake hoses, wheel-speed-sensor wiring, and mounting fasteners. Replace damaged or manufacturer-designated single-use hardware as required. Do not loosen the center strut-shaft nut unless the applicable service procedure and proper spring-compression equipment are being used.
Tighten all fasteners using the vehicle manufacturer's sequence and torque specifications, with suspension pivot fasteners tightened at the specified ride-height position where required. Verify brake-hose and sensor-wire routing, wheel and tire clearance, and freedom from interference through the full steering range.
After installation, perform a four-wheel alignment and inspect ride height, steering-wheel position, braking behavior, warning lights, abnormal noise, and fastener security. Conduct the initial road test in a controlled area before normal driving.
Frequently Asked Questions
Are both front sides included?
Yes. The source lists a two-piece set for the driver and passenger sides.
Are the coil springs included?
Yes. The source describes complete strut and coil-spring assemblies.
Are upper mounts and bearings included?
The source does not separately itemize upper mounts, bearings, isolators, boots, or bump stops. Confirm these components from the product images before ordering.
Does this fit GT, Shelby, Coupe, and Convertible models?
The source does not distinguish engines, trims, body styles, or suspension packages. Verify the VIN and compare the original suspension before ordering.
Is an alignment required?
A four-wheel alignment is recommended after front strut replacement to check and correct suspension geometry.
Couldn't load pickup availability
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Quick order list
Clients Love Us
Stephanie L.
Ordered the BMW front bumper fog light grille and the fitment was absolutely perfect. Gloss black finish looks factory-fresh and the quality is outstanding. Installation took about 30 minutes — no drilling required. Highly recommend AlchemyRide!
Marcus R.
Fast shipping, great packaging, and the part arrived in perfect condition. The grille fits my F23 like a glove — exactly as described. Customer service was also super responsive when I had a fitment question. Will definitely order again.
David K.
I've bought aftermarket parts from many stores but AlchemyRide stands out for quality and value. The part was well-made, fit perfectly, and the price was very competitive. My BMW looks aggressive and clean — exactly what I wanted.
Jenny T.
Excellent product and super easy to install. The gloss black finish matches my M Sport bumpers perfectly. Shipping was faster than expected and the part was well-packaged. Very happy with my purchase — my car looks completely transformed!