Bentley Bentayga 2016–2022 Carbon Fiber Side Skirts

Carbon Fiber Side Skirts for Bentley Bentayga

Define the lower side profile of a compatible Bentley Bentayga with high-gloss carbon fiber side skirts. The listed 3×3 carbon weave adds a distinctive exterior styling detail along the rocker area.

Vehicle Fitment

• Model: Bentley Bentayga.
• Source-listed years: 2016–2022.
• Body style: Sport Utility, 4-Door.
• Position: Lower side skirt / rocker trim area.
• Source-described design: Replacement for the factory side skirts.

Confirm production date, actual wheelbase, original sill length, skirt profile and mounting points before purchase. The source does not provide a separate compatibility chart for facelift revisions, trims, standard versus extended wheelbase or regional specifications. The broad model and year range does not establish that different sill lengths or skirt designs are interchangeable.

Check any fitted running boards, powered side steps, mud flaps and aftermarket underbody or side trim. Compatibility with these components is not documented. Vehicles with modified skirts require individual assessment.

Material and Finish

• Carbon fiber construction: Specified in the original features.
• 3×3 weave: The listed carbon pattern.
• High-gloss finish: A reflective exterior appearance.
• UV-resistant coating: A stated finish feature.

Dry-carbon construction, prepreg, autoclave or vacuum processing, backing material and laminate thickness are not specified. Measured weight savings, quantified strength and permanent resistance to fading or yellowing are not established. No aerodynamic, downforce, handling, fuel-economy or structural-protection improvement is claimed.

Contents and Component Scope

• Carbon fiber side skirts.
• Self-tapping screws, stated as included.

Exact piece count, supplied sides, section layout and fastener quantity are not itemized. The plural name does not independently establish a two-piece left-and-right set. Confirm the complete contents before ordering. Clips, brackets, adhesive tape, bonding products, tools and running boards are not individually listed as included.

The source describes replacement of the factory skirts, but does not explain the removal procedure or which original mounting components remain in use. Confirm the exact part coverage and retained trim before dismantling the vehicle. These exterior styling parts are not structural rocker panels, jacking points or load-bearing steps; do not stand on them or use them to support the vehicle.

Mounting Clarification

The original description combines bolt-on / no-modification wording with included self-tapping screws. This does not establish that existing mounting holes are sufficient or that drilling is unnecessary. Obtain product-specific instructions showing every mounting location, required original hardware and any additional attachment requirements.

Do not assume supplied screws replace all original clips and brackets. Do not substitute unspecified tape for mechanical retention, or drill structural sill areas based solely on general Direct Fit wording.

Professional Installation and Clearance Checks

Professional installation is recommended. Use appropriate lifting equipment and vehicle-specific approved support points when access beneath the vehicle is needed. Trial-fit all supplied sections before drilling, cutting or applying any separately specified adhesive.

• Verify skirt length, contours, mounting points and side identification against the actual vehicle.
• Confirm factory skirt removal and any retained brackets, clips, seals and underbody panels.
• Check clearance through the full door opening range and operation of any fitted powered side steps.
• Preserve access to approved jacking points and keep drainage paths and service access unobstructed.
• Inspect behind intended fastener locations for wiring, lines and other components before drilling.
• Use the specified attachment arrangement without forcing misaligned trim into position.
• Assess tire, wheel-arch and adjacent-panel clearance where relevant.
• Check road, ramp and driveway clearance across the vehicle's permitted suspension-height settings where fitted.
• Confirm secure retention, unobstructed doors and absence of rubbing before driving, then recheck attachment as directed by the installer.

If the actual fitting instructions require additional adhesive or sealant, follow its preparation and curing requirements; inclusion is not established here. Do not drive with loose skirts or uncertain attachment. No fixed installation time or universal no-cutting / no-drilling fit is promised.

Care

Use a soft cloth and products suitable for coated carbon fiber. Avoid abrasive treatment and periodically inspect the underside, edges and mounting points, especially after ground contact. Do not use the skirts as steps.

Frequently Asked Questions

Are these replacement side skirts?
The source describes replacement of the factory skirts. Confirm the exact component coverage and retained original hardware before removal.

Do these fit extended-wheelbase vehicles?
No wheelbase-specific fitment chart is provided. Confirm actual sill length and mounting geometry rather than assuming compatibility.

Is a left-and-right pair included?
Exact piece count and supplied sides are not itemized. Confirm the complete configuration before purchase.

Are these dry carbon fiber?
The source specifies carbon fiber and 3×3 weave but does not identify dry-carbon construction or a curing process.

Are screws or tape included?
Self-tapping screws are listed. Tape is not separately listed as included.

Is installation guaranteed to require no drilling?
No. The source does not establish that existing holes suffice; confirm product-specific fitting instructions.

Can the skirts be used as running boards?
No. These are exterior styling parts, not load-bearing steps or vehicle support points.