Maserati Ghibli Sedan Carbon Fiber Replacement Hood / Bonnet, 2014–2020

Carbon Fiber Replacement Hood for Maserati Ghibli Sedan

Add a gloss carbon-fiber exterior finish to your listed Ghibli with this replacement-style hood, also called a bonnet. Although the original name includes “cover,” the detailed source specifies replacement installation using factory screws. This listing is not presented as a tape-on overlay or an under-hood engine cover.

Listed Vehicle Fitment

• Maserati Ghibli Sedan.
• Named configurations: Base, S, S Q4, Diesel and 250 Diesel.
• Source-listed years: 2014, 2015, 2016, 2017, 2018, 2019 and 2020.

Confirm VIN, production date, regional model year, exact configuration and original hood mounting arrangement before ordering. The combined configurations and year range are not a verified model-by-year table. Check facelift, regional specification and under-hood equipment differences individually. The “250 Diesel” designation is retained as listed by the source, not interpreted as an engine displacement.

GranLusso appears in a search tag but is not separately documented in the detailed fitment. GranLusso, GranSport, Trofeo, Hybrid, later years and other unlisted configurations require separate verification; tags do not independently establish compatibility.

Material and Finish

• Specified material: 3×3 weave carbon fiber.
• Gloss surface with a double-layer UV-protected clear coating.

A dry-carbon process, full laminate composition, underside structure, reinforcement design, curing method, dimensions and measured hood weight are not supplied. Pure-carbon-throughout construction, measured weight savings and permanent resistance to fading are not established. The supplied information does not confirm functional vents or a specific vent layout.

Replacement Structure and Package Scope

The source identifies a replacement-style hood and instructs use of factory screws. This does not confirm a complete ready-to-install assembly with all hardware and equipment attached. An itemized packing list and molded section count are not supplied.

Hinges, primary latch, secondary safety catch, striker, support struts, insulation, seals, washer fittings, sensors, wiring and active hood components are not specified as included. Confirm which original components can be transferred and whether additional components are required before removing the original hood. New screws, tape and brackets are not listed as included.

Safety-Critical Fitment Checks

Professional installation and hood-retention assessment are required. Have a qualified installer verify hinge geometry, reinforced attachment points, fastener specifications, striker position, primary latch engagement and secondary safety retention. A generic instruction to reuse factory screws does not establish that every original fastener is suitable or reusable; follow applicable vehicle and component installation specifications.

Confirm compatibility with hood support struts and their loads, release cable operation, hood-ajar sensing and any active hood/pedestrian-protection equipment where fitted. Do not disable or bypass safety systems to make the hood fit. The source does not establish that original crash or pedestrian-protection performance is retained.

The supplied details do not confirm whether supplemental retention hardware is required. Obtain a verified installation specification for this exact hood rather than assuming the original latch alone is sufficient. Do not drive until a qualified installer has confirmed secure retention and correct operation.

Installation Guidance

Test-fit before drilling, modifying mounting points or transferring original equipment permanently. Check panel gaps and alignment with the fenders, front fascia and cowl, plus clearance to the windshield and wipers throughout the full opening movement.

Verify clearance to the engine and other under-hood components, appropriate heat management, insulation and seals where required. Preserve washer operation, wiring routing, drainage and service access. Do not assume that a carbon-fiber exterior finish replaces factory heat shielding.

Confirm smooth opening and closing, reliable release and secure latch engagement without forcing or slamming a misaligned panel. Recheck mounting hardware and retention according to the installer's guidance. No-drill fitment, no-modification installation and a fixed installation time are not promised.

Performance Scope

This listing describes an exterior replacement panel. No measured aerodynamic, cooling, weight-reduction or handling results are supplied, so performance improvements and structural protection are not promised.

Frequently Asked Questions

Is this a tape-on hood cover?
No. The detailed source describes replacement-style installation using factory screws.

Are latch, hinges and support struts supplied?
They are not specified as included. Confirm component transfer and additional hardware requirements before removal of the original hood.

Can factory screws simply be reused?
The source calls for factory screws, but a qualified installer must verify the correct specifications, condition and reuse suitability.

Is original safety-system compatibility guaranteed?
No. Latches, retention, sensing and any active hood equipment need individual assessment before use.

Is this dry carbon or a verified weight-saving panel?
The source specifies 3×3 carbon fiber without a confirmed dry-carbon process or measured hood weight.