Mercedes-Benz W176 A-Class Carbon Fiber Replacement Hood / Bonnet, 2013–2018

Carbon Fiber Replacement Hood for Mercedes-Benz W176 A-Class

Bring a gloss carbon-fiber finish to the front of your listed W176 A-Class hatchback. The detailed source identifies this bonnet as a replacement-style panel using factory screws. Despite the original “hood cover” wording, it is not presented as a tape-on overlay or a cover for the engine beneath the hood.

Listed Vehicle Fitment

• Mercedes-Benz A-Class W176 Hatchback.
• Named configurations: A180, A200, A250 and A45 AMG.
• Source-listed years: 2013, 2014, 2015, 2016, 2017 and 2018.

Confirm VIN, production date, regional model year, chassis and original hood mounting arrangement before ordering. The combined models and years are not a verified model-by-year compatibility table. Check facelift differences, engine-bay equipment and exact A45 AMG specification individually; a shared chassis label does not establish identical mounting or clearance on every configuration.

The original hidden filters also contain 2019, diesel/CDI/d designations, A220 CDI and drivetrain-specific entries. These do not expand the detailed fitment above. Diesel applications and individual drivetrain configurations require separate verification. This listing does not confirm W177, A-Class Sedan, CLA or GLA compatibility.

Material and Finish

• Specified material: 3×3 weave carbon fiber.
• Gloss surface with a double-layer UV-protected clear coating.

The source does not specify a dry-carbon process, pre-impregnated cloth, full laminate composition, curing method, underside reinforcement, dimensions or measured hood weight. Pure-carbon-throughout construction, quantified weight savings and permanent resistance to fading are not established. Functional vents and a particular vent layout are not confirmed.

Replacement Structure and Package Scope

The source specifies replacement installation using factory screws and recommends professional installation. It does not establish a complete ready-to-install assembly with all original equipment attached. An itemized packing list and molded section count are not supplied.

Hinges, latch, striker, secondary safety catch, support hardware, insulation, seals, washer fittings, sensors, wiring and active hood components are not specified as included. Confirm which original components can be transferred, which need replacement and whether additional hardware is required before removing the original bonnet. New screws, tape and brackets are not listed as included.

Safety-Critical Fitment Checks

Professional installation and hood-retention assessment are required. Have a qualified installer verify hinge geometry, reinforced mounting points, fastener specifications, striker alignment, full primary latch engagement and secondary safety retention. The source instruction to use factory screws does not establish that every original fastener is suitable or reusable; use the applicable vehicle and component installation specifications.

Confirm compatibility with the original hood support arrangement, release mechanism, hood-ajar sensing and any active hood or pedestrian-protection equipment where fitted. Do not disable or bypass safety systems to make the panel fit. Retention of original crash or pedestrian-protection performance is not established by the supplied information.

The source does not confirm whether supplemental retention hardware is required. Obtain a verified installation specification for this exact hood rather than assuming the original latch alone is sufficient. Do not drive until a qualified installer has confirmed secure retention and correct operation.

Installation Guidance

Test-fit before drilling, modifying attachment points or permanently transferring original equipment. Check panel gaps and alignment with the fenders, front fascia and cowl, plus windshield and wiper clearance throughout the full opening movement. Do not force or slam a misaligned panel.

Verify clearance to the engine and under-hood components, appropriate heat management, insulation and seals where required. Preserve washer operation, wiring routing, drainage and service access. A carbon-fiber exterior finish is not confirmation that original heat shielding can be removed.

Check smooth opening and closing, reliable release operation and secure latch engagement. Reinspect mounting hardware and retention according to the installer's guidance. No-drill fitment, no-modification installation and a fixed installation time are not promised.

Performance Scope

This listing describes an exterior replacement panel. No measured aerodynamic, cooling, handling or weight-reduction results are supplied, so performance improvements and structural protection are not promised.

Frequently Asked Questions

Is this a tape-on hood cover?
No. The detailed source describes replacement installation using factory screws.

Are hinges, latch and support hardware included?
They are not specified as included. Confirm component transfer and any additional hardware before removing the original hood.

Does it fit every W176 diesel or a 2019 vehicle?
Those applications appear in filters but are not confirmed by the detailed fitment. Verify them separately rather than extending the listed range.

Is it dry carbon?
The source specifies 3×3 carbon fiber but does not establish a dry-carbon process or full laminate construction.

Can it be installed without checking the safety equipment?
No. Mounting, latch retention, support equipment and any active hood systems need professional assessment before use.